STM32 ST Link – Windows-приложение для программирования популярных чипов. Предусмотрено два режима работы – классический графический интерфейс и командная строка. Необходимо физическое подключение специального программатора, который обеспечит корректное взаимодействие ПК с чипом. При этом приложение позволяет автоматически распознавать тип подключенного модуля, что упрощает работу в целом.
Подключение
После инсталляции программы необходимо подключить плату к свободному порту ПК и только после этого открыть основную утилиту. Далее требуется указать активный порт для передачи пакетов данных и дождаться сообщения о корректном распознавании устройства. В случае успеха отобразится информация о подключенной модели платы, точная версия прошивки и другие служебные данные, которые облегчают работу.
Программирование
Перед записью новой прошивки необходимо инициировать очистку памяти. Для этого достаточно открыть меню «Target» и активировать опцию «Erase Chip». Для загрузки нового образа требуется активировать соответствующий пункт основного меню и через окно проводника указать путь к файлу BIN или HEX. Встроен редактор данных, который позволяет открыть содержимое прошивки в удобном формате и внести изменения.
Кнопка «Program» запускает процесс записи подготовленного набора данных. Есть возможность предварительно сравнить между собой две версии прошивки, а также использовать режим автоматического поиска ошибок в коде.
Особенности
- утилита позволяет очищать и программировать микроконтроллеры;
- поддерживаются чипы серии STM32;
- режим сравнения прошивок и поиска ошибок в коде;
- встроенный редактор;
- поддерживаются образы в формате BIN и HEX;
- программа является бесплатной.
Provide feedback
Saved searches
Use saved searches to filter your results more quickly
Sign up
When attempting to download HP Smart, the first step is to ensure that your device meets the operating system requirements for the application. After confirming that you meet these requirements, then you should access the official download webpage on either your mobile device or computer. There, you will be able to download and install HP Smart. Once installed, open up the application and follow any further instructions.
If you are experiencing problems with your Pantum M6550NW printer, be sure to check the manufacturer’s website for troubleshooting and support options. Additionally, you should make sure that the printer is up-to-date with the latest firmware version. Troubleshooting steps such as restarting both devices (printer & PC/Laptop) or checking cables can help in many scenarios too.
If you are having issues with the Pantum M6550nw driver, please go to https://www.pantum.com/download and select your printer model from the drop-down menu to download and install the correct driver for your system.
Troubleshooting Microsoft Issues can be a time-consuming and complicated process. The goal of this guide is to provide a step-by-step approach to troubleshoot any issues with Microsoft products. We’ll start by providing general advice for diagnosing the problem and then review troubleshooting techniques specific to different types of Microsoft services, such as Windows, Office, or Azure services. With this comprehensive roadmap in hand, you should find yourself better equipped to identify and resolve even complex issues quickly.
Realtek can cause a range of issues that can be difficult to troubleshoot without the right expertise. This comprehensive guide covers everything you need to know for troubleshooting Realtek problems so that you can get back on track quickly and easily.
software that may be blocking TeamViewer. Many firewalls and antivirus programs will block the connection unless you explicitly allow it.
Driver packs are collections of drivers that can be used to update outdated or missing device drivers. If you are having trouble with driver pack, the best thing you can do is use a trusted and reliable driver updater tool to automatically download and install the correct version of the required drivers for your PC. This will ensure all your devices are running on their latest available software.
If you are looking to download the driver for your Canon Pixma MG2500 printer, you can do so from the official Canon website. Simply go to their online support page and search for the model number of your printer. Once selected, click on ‘Drivers & Downloads’ tab and choose your operating system to get access to a list of all available downloads related to that particular model.
If you’re having issues with your Epson L4150 Printer software, try updating the software by downloading and installing the latest version from Epson’s website. You can also refer to their troubleshooting guide for more help on resolving any issues.
KMS Pico is a powerful tool that can be used to activate Windows 10. It works by emulating the Microsoft KMS server on your computer, allowing you to bypass activation processes and activate your copy of Windows for free. To fix this user query, simply download the latest version of KMS Pico from a trusted source and follow the installation instructions when prompted.
See all queries
Once you have your ST board that may be either discovery, Nucleo, or any other board from ST, which is based on ST-Link in-circuit debugger and programmer, then in order to talk to the board successfully, you have to install the ST-Link drivers.
The ST-Link driver means the driver for the ST-Link in-circuit debugger and programmer interface, as depicted in Figure 1.
ST-LINK Driver for Windows (32/ 64-bit versions 7, 8, and 10):
It is available on the STs website.
- Visit the ST website and navigate to STSW-LINK009, as indicated in Figure 2. You will get a USB driver for those boards with ST-LINK/V2 and ST-LINK/V2-1 ST-Link circuitry.
At the end of the website, you will find the driver link (Figure 3), and proceed to download it.
- Upon downloading, access the folder where the driver is stored. Within it, you’ll find two applications (Figure 4), one for 32-bit and the other for 64-bit systems.
- Now connect your board.
It could be either discovery or Nucleo. Launch the downloaded driver software. A popup window (Figure 5) appears. Proceed by clicking “Next.”
- The software will install the WinUSB driver (Figure 6), which is required in order to talk to the ST-Link, and it also installs other drivers. Upon completion of the installation, click “Finish” (Figure 7).
- See your device manager. When your Nucleo board is connected, a COM port will be visible under “Ports,” and the “STMicroelectronics STLink dongle” option will appear in “USB devices” (Figure
In order to communicate with the board over UART, you use the ST-Link Virtual COM Port interface, and your host application or host IDE uses STMicroelectronics STLink dongle interface, which is an interface used for debugging.
Remember, the correct installation of the ST-Link driver is of utmost importance upon obtaining your board.
ST-LINK Driver for Ubuntu:
For Ubuntu users:
- Follow the commands displayed in Figure 9 using your command prompt to install the necessary packages. Notably, ST doesn’t offer specific drivers for Ubuntu or MAC, hence Ubuntu users should proceed with package installations as indicated.
ST-LINK Driver for MAC:
Fortunately, no driver installation is required for MAC systems.
In the following article, let’s learn ST Link Firmware Upgrade.
FastBit Embedded Brain Academy Courses
click here:https://fastbitlab.com/course1
FastBitLab
The FastBit Embedded Brain Academy uses the power of internet to bring the online courses related to the field of embedded system programming, Real time operating system, Embedded Linux systems, etc at your finger tip with very low cost. Backed with strong experience of industry, we have produced lots of courses with the customer enrolment over 3000+ across 100+ countries.
-
STM32
-
stlink
-
драйвер
-
Ответить
-
Создать новую тему
Рекомендуемые сообщения
-
- Поделиться
Здравствуйте. У st.com, похоже, что-то сломалось, и драйвер не скачивается. Скиньте, пожалуйста, установщик драйвера.
Ссылка на комментарий
Поделиться на другие сайты
ERID: 5jtCeReNx12oajt53wT4Zno
-
- Поделиться
Ссылка на комментарий
Поделиться на другие сайты
- 6 лет спустя…
-
- Поделиться
Тема похожая спрошу тут.
Получил линк-2, и не могу проверить годный, или нет.
С СТМ еще не имел дела, первый опыт, подскажите , без программируемого чипа программатор должен определяться и видится в проге???
У меня такое выдает
И даже когда вроде определился, все равно не работает.
Без подключенного чипа должен работать???
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
Попробуйте обновить Firmware через STM32 ST-LINK Utility.
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
О заработало, вчера ни на какой проге не работало.
Ссылка на комментарий
Поделиться на другие сайты
Присоединяйтесь к обсуждению
Вы можете написать сейчас и зарегистрироваться позже.
Если у вас есть аккаунт, авторизуйтесь, чтобы опубликовать от имени своего аккаунта.
Примечание: Ваш пост будет проверен модератором, прежде чем станет видимым.
-
Последние посетители
0 пользователей онлайн
- Ни одного зарегистрированного пользователя не просматривает данную страницу
-
Сообщения
-
Автор
Александр Матроскин · Опубликовано
@Владислав2 дело не в сложности, а в том что в них съэкономили просто на всем чем можно, дроселя (не в этом, но по входу часто у них просто перемычки), конденсаторы, радиаторы даже клеммы порой из какой то консервной банки по ощущениям. Комплексный анализ и разбор причин конечно я не делал, но такие приколы как у ТС, с ними были постоянно. Плюсом еще жуткий уровень пульсаций, стабилизация только 12в линии (на некоторых моделях), в общем ни чего хорошего от них ждать не приходиться.
-
Автор
Владислав2 · Опубликовано
Вообще, никогда не задумывался. Фолькдойч — вы большой молодец. Начальнику между делом скажу — посмотрю на лицо..
Не зря я на паяльнике сижу… Жизнь удалась.
-
Автор
Том · Опубликовано
Вчера слепил за полчаса и выложил, проверил только на генераторе — на много лучше сигнал снимает, это чистая медь, сейчас попробовал согнуть — вполне себе ничего.
Чутка.
-
Автор
Владислав2 · Опубликовано
У меня валяется «видик». Реально лень туда лезть.
Там «командоаппарат» чистить надо. Кассета заела на выходе.
Цепи аудио сигнала. Электролитические конденсаторы. Они там низко профильные. Я бы керамику поставил сейчас, смд. Как то делал, лет 15 назад…
Проверял обычным унч с цепью ООС. Не было тогда ЕСР метров. У меня.
Целый конденсатор в цепи ООС режет усиление. С потерей ЕСР испытуемого конденсатора будет подъём вч. Понятно, надо под 8 — 10 кГц тестовый сигнал. Можно и выше, если не глухня — как я.
-
Автор
Владислав2 · Опубликовано
Тоже, сложные случаи не делаю. Дохлых бп с управления пачками носят. 4 Корсайра восстановил. Ещё один валяется.
На донора — хороший вариант. Хотя.. у каждого своё мнение и желание. И возможности. Но я бы делать не стал.
-
Похожий контент
-
77
Автор
WaRLoC
Started -
5
Автор
WiSmth
Started